This can result in an unstable piece of furniture that can wobble or tip over.Ģ. On drawers that hold heavy items, stabilizer screws are often used, so it’s very important to remove them from top to bottom to prevent the piece of furniture from becoming top heavy. Be sure to work on the drawers in the proper order, by starting at the top and moving down drawer by drawer. Even so, these drawers and screws come out relatively easily. In some cases, the drawers in your furniture will have stabilizer screws, which add an extra step to the drawer-removal process. Either way, pull with enough force to overcome the resistance. If your furniture uses one center wooden track, it will take a bit more effort to remove the drawer, while wood-glide furniture with two side tracks will be a bit easier to work with. Use both hands and a bit of force to tug the drawer out toward your body as evenly as possible. Don’t worry about pulling it too far because most drawers have a natural stopping point.ģ. This helps to prevent a situation where top-heavy furniture can topple over, although if the body of the furniture is very heavy, this won’t be an issue.Ģ. Start with the top drawer, and move from the top to the bottom. These drawers often don’t open as smoothly, but they can be removed with a solid tug, as described here:ġ. Wood-drawer slides are often found on older furniture like armoires or dressers. You might need to tilt the drawer downward to fully remove it. Continue pulling the drawer outward until it is completely off of the rails. If the drawer guides have a lever, push it while pulling the drawer out.Ĥ. Check the drawer guides to see if there is a clip or locking lever. Pull the drawer open until it’s as far out as possible and the guides are fully extended.ģ. If you need to remove soft-close drawers, follow these simple steps:ġ. Unlike typical rollers and rails, this type of drawer guide helps prevent drawers from being shut too hard-potentially preventing damage-and will also gently slide closed over the last few inches, even if the drawer was not pushed hard enough. Soft-close drawers are often found on custom cabinets and higher-end furniture. The tracks will likely stick out from the front after the drawer has been removed, so push them back with a straight, parallel motion. It should easily lift out of the furniture. Hold down the levers, and pull the drawer out toward your body. For a curved lever, you’ll need to push on the curved area until it flattens out.ĥ. If it’s a straight lever, this process is extremely simple: just press down as far as you can. Use both hands to simultaneously press both levers. Full-extension drawer slides will typically have straight levers, while three-quarter slides (more common on smaller drawers) will probably have a curved-track disconnect lever.Ĥ.
They will be either straight or curved depending on your particular piece of furniture. Locate the track levers, which should be in the center of each drawer track. Don’t stand too close-leave enough space to allow the drawer to open to its natural stopping point.ģ. Stand in front of the piece of furniture and slide the drawer open as far as you can, with one hand on each side of the drawer.
Starting at the top and working down is safest and easiest because it keeps the bulk of the weight at the bottom.Ģ. This prevents the furniture from becoming top heavy, which may be dangerous and can result in the furniture tipping over. This rule applies to any type of furniture with drawers if you need to work on more than one drawer, start at the top and work your way down. To remove drawers from a metal glide, follow these steps:ġ. Metal-glide slides with levers are the most common type of drawer slide, so there’s a good chance your furniture is equipped with this kind of hardware. Below are instructions for removing drawers from the most common types of drawer slides. The process of removing drawers is usually simple, but it will vary depending on the type of drawer slides you're working with. Whether you’re moving the furniture and need to make it lighter before transport, cleaning the piece out, or if you need to make a quick repair, removing the drawers is usually the first step.
METAL BOX SINGLE WALL DRAWER SLIDE RUNNER RAIL HOW TO
How to Remove Drawers With the Most Common Types of Drawer SlidesĪt some point, you'll probably find a reason to remove the drawers from one of your cabinets, dressers, or a similar piece of furniture.
0 kommentar(er)
